- #Behringer uca202 audio interface krk speakers manual
- #Behringer uca202 audio interface krk speakers software
If your interface has a mono/stereo selector switch, then you can use one channel as the left input and the other as the right by selecting stereo mode. To input in stereo you would send each stereo channel (left and right) into a separate input on the interface.
#Behringer uca202 audio interface krk speakers software
An audio interface will output into your computer where your DAW software can render two channels in stereo.
To do this properly, you will need to understand how your particular interface works and then use the appropriate cable to connect it. I am sure you want the stereo signal to be routed into your interface so that it can then be routed into your computer and maintain the stereo separation selected on your mixer. In mixer and interface applications, this is more commonly true than using the TRS tipped cable to transmit a stereo signal.įor the application you described, it sounds as if you wish to send the two individual outputs from the two channels on your mixer as a stereo (left and right) signal into your audio interface. In many cases a TRS connector is used on a two core balanced cable to deliver a balanced signal which will reduce electrical interference and hum instead of an unbalanced signal form a single core cable and TS connector. You will find this scenario on stereo headphones. The output jack must be wired as a TRS output in order to route the separate stereo channels into the appropriate wires inside the cable. So my guess is you want to get 2 TRS cables, one for left and one for right, and with a bit of luck that should give you balanced, stereo connection.Īs I am sure you are aware - the TRS connector tip is capable of transmitting a stereo signal (separate left and right signal) from a stereo output jack to a stereo input.
#Behringer uca202 audio interface krk speakers manual
The Yamaha manual says it has "TRS phone-jack type balanced outputs" the Focusrite manual says "Set the LINE/INST switch next to the socket.to LINE if you are connecting a line level source such as the balanced output of a stage piano via a 3-pole (TRS) jack." (but for 'stage piano' there, we can read 'mixer') In summary, you're unlikely to do any harm mixing up stereo and mono cables, but it's a good idea to know the contact arrangement in the equipment you're plugging into so you can use it as designed. When it comes to balanced or unbalanced audio, many sockets are designed so that plugging in a TS jack gives you an unbalanced connection, while a TRS allows a balanced connection to whatever's at the other end of the cable. If you were to plug a stereo (TRS) plug into a mono (TS or TR) socket, you'd get your mono signal coming down either the left or the right channel (probably the left, as this is usually the tip), but you'd leave your right input channel 'floating', which is not ideal. If you had a stereo output socket (TRS) and plugged in a mono plug with only the tip and the sleeve, you'd be grounding one of the channels (probably the right, which is usually wired to the ring) which is not a great thing to do ( ), and you'd only get the left channel coming over the cable.
as a mono send/mono return for an insert effect (like a compressor on one channel of a mixer), or as a balanced signal carrier. This could be used for stereo purposes, but it could also be used for other things : e.g. TRS (Tip-Ring-Sleeve) is the name often given to the connector, rather than the cable as such, though of course they would usually be used with a 3-conductor cable. It may well be that you decide to use the Main Out for them, feed the audio interface from the Group sends.) (As well as the connection to the Focusrite Scarlett 2i2, you will have to decide where to attach your monitor speakers. There is no way of using a single "stereo" cable.
In practice, I can confidently state there will be no discernable difference. The balanced option has theoretical advantages.
If you use a 2-conductor cable with TS jack plugs you will get an unbalanced one. If you use a pair of 3-conductor cables, with TRS jack plugs, you will get a balanced connection. Your Focusrite Scarlett 2i2 has combo jacks, accepting a microphone signal on an XLR plug or a Line input on a TRS jack. But we don't need to worry about that for now.) (The outputs are duplicated on a pair of balanced XLR sockets, which carry an identical electrical signal. Your yamaha mg124cx has its stereo main outputs arranged as a pair of balanced TRS 1/4" jacks. Now you've asked a specific question, you can have a specific answer!